I'm sorry for the delay and the time which has lapsed since my last post. I have been receiving numerous emails from individuals asking for more posts or information about keeping bees. I just recently received an email from a future beekeeper here in the state and I would like to share some of the questions and answers to any future or beginning beekeepers who may take the time to read this.
"We're working on getting our first hives/bees, and would like some information/advice, if you have it!"
The first thing you should do is to put in your orders now. Package bees and nuc colonies sale out quick so go ahead and put in an order. Don't just get one colony, try to get at least two. This way you can compare their development with one another. You can also swap brood from a strong colony to weak one if the should arise. These are just a few examples of why you should have at least two colonies and other reasons shall become more apparent when you begin to work with your bees.
Be sure to put in your order for your woodenware as early as possible as well. The spring time is the busiest time of year for the supply houses. You should have your new hive assembled and painted and waiting on your package to arrive. Or maybe you should have it ready in advance to catch a swarm.I don't know how many times I had to put wax foundation into frames in order to go out and retrieve a swarm. Be prepared and do not procrastinate. Procrastination is one of the worst things you could do when it comes to your bees.
The easiest thing to do is to purchase an established colony. Anyone selling bees in the state are required to first have their colony inspected by a state apiarist to insure it is disease free, (actually all colonies within the apiary must bee examined and deemed disease free before any one of the colonies can be sold.) The state inspector will give the beekeeper a certificate of health when after the colonies are inspected and deemed free of disease and parasites. Be sure to ask to see the certificate before making a purchase. A strong and healthy colony should produce you a surplus of honey the first year that you have it.
If you choose to buy a package of bees, keep in mind you will also need to buy the hive components to install the package. You will also need to continuously feed the package sugar syrup in order for them to draw out their broodnest and accumulate enough stores of honey for the upcoming winter. Packages are inspected in the state of their origin before being shipped abroad so there is no need to worry of that. One large drawback of purchasing a package of bees is the possibility that it may abscond once you install in your new hive. By the time you purchase your equipment and pay the price of the package it may be equivalent to that of an established colony as mentioned above.
Nucleus colonies, or "nucs" as they are more commonly referred to, is a good step up from a package of bees. A nuc also needs to build in strength and be fed sugar syrup to help it build comb. raise brood, and accumulate enough winter stores to survive until the following year. You also have to buy additional woodenware as the nuc expands it broodnest as you do with a package. Nucs are much less likely to abscond than a package. If purchased early enough in the spring, a nuc could build up to a strength sufficient enough to produce a surplus of honey. Once again, nucs are inspected for disease and parasites in their state of origin before it is legal to sale them.
You could join your local bee clubs to meet some local beekeepers. This is a great way to possibly score a free swarm of bees in the early spring. I personally like swarms (provided it came from some other beekeepers colony), the earlier the better. In my opinion, they have a drive to survive that exceeds that of a nuc or package and build up much quicker. I have had new colonies from swarms that have provided me a harvest of honey from building up so quickly. In our area, WV, we do not have to worry about AHB, Africanized Honeybees, as do our fellow beekeepers in the southern states, so you beekeepers in AHB territory be careful when collecting swarms this spring!!!
"What do you suggest, as far as set up kits go (we do have a Better Bee catalog, and I've wandered about the internet looking at various apiary sites). Wood? Polystyrene? Is one company better to deal with than another? If there is a 'beginners book' that you would consider a must-have - what would it be? Anything else we need to look at or should consider?"
I personally buy what I don't make myself from Walter T Kelley. The prices are fair and they produce a quality product. Having never used any polystyrene hive components, I prefer wooden equipment. Most of the supply companies are like any other business, they all get good and bad reports. I can say that I can not say anything ill towards Kelley's and I have developed a personal rapport with one of their sales agents. Their are plenty of books and educational materials for beekeepers to use in order to become better beekeepers. Bees are the most studied insect in the past and present so you can much on the subject. I went to my local library last winter and found a nice book on the subject to check out and read. Also, you could get a subscription to "American Bee Journal" or "Bee Culture." There is a lot of up to date information on new studies and goings on in the world of beekeeping. The best thing you could do is to try be as well as informed as possible so your bees will appreciate you more. By appreciate I mean that you can institute methods into your beekeeping to keep them healthier, hygienic, gentle, fecundate, populous, gentle, and disease free. If you do good by your bees they will do good for you.
"We have spoken with a bee keeper in Ohio, but it seems he's very much pressing to buy his stuff ("Forget the catalog! I got it all!") and since we are so very new to the idea, I thought I'd find another WV beekeeper and ask for their opinion - and I found you."
I am honored that you would ask my opinion. As you talk to more beekeepers you will find that there are many different beliefs and opinions in regards to the same questions you may have. Though I have a good working knowledge about bees, I still have much to learn. Regarding the Buckeye Beekeeper, I would try to stay away from any used equipment and purchase new equipment. used hive bodies and frames could contain the spores of American Foul Brood (AFB). The only cure for this brood disease id to destroy the colony. The bees and all hive components are typically destroyed my burning them. Though AFB contaminated is safe for human consumption, it can easily spread the disease from colony to colony through the act of "robbing". I would hate to see your investment and hard work go up in flames because you did spend a few extra dollars to purchase new equipment for your bees. If the Buckeye Beekeeper is wanting to sell you new homemade equipment, make sure all components are of the standard dimensions of the Langstroth hive bodies and supers. I've seen some homemade jobs which were totally incompatible with the store bought stuff. This is okay sometimes, but it does create problems like violation of "bee space" and could result in excessive burr or bridge comb which would make hive inspections more of a chore than a joy.
If you have anymore quetions about getting your first colony please let me know.
Merry Christmas fellow beekeepers.
Showing posts with label bee hive. Show all posts
Showing posts with label bee hive. Show all posts
Sunday, December 21, 2008
Saturday, January 5, 2008
Repairing Hive Bodies
After a while of having an apiary almost every beekeeper is faced with the dilemma of repairing or replacing some of their woodenware. For me the most common piece of woodenware which needs to be replaced or restored are the hive bodies. The hive bodies which contain the brood and winter cluster are subject to all weather conditions every day of the year. Your honey supers usually only experience seasonal usage during which they are in warmer weather and not subject to being damp for extended periods of time through the winter like the hive bodies for the brood chamber are.
Most of the hive bodies that I use are deeps (9 5/8" tall). The deeps are much heavier when full of honey than my shallow supers are when they are full. The extra amount of pressure used to pry them apart with my hive tool also helps to damage them. After they have been in the weather for a few years the corners where you pry them apart degrade due to the weather so it becomes easier to damage them when prying them apart.
A few years ago I went to a hive body rotation schedule due to having older hive bodies which needed repaired or restored. During the winter months I will repair and restore some of the older hive bodies to rotate out with those currently in use. I like to switch them out in the spring when I start to routinely inspect my colonies. The ones which get rotated out will soon be restored or repaired with a fresh coat of primer and paint to be put back into rotation when needed. After I am finished with the rotation the last ones will usually sit around until January at which point I will start getting anxious and start the process again. The winter months are also an excellent time to buy all that new woodenware you need for the spring.
I am sure that some of you have seen hive bodies that look like this.
Sometimes when I have a hive body like this I will cut them down to a medium super (6 5/8" tall). That is the easiest thing to do. The only bad thing is that you either have to cut down some frames to fit it or just buy some new ones. You can see at the bottom left, or a top corner, of the hive body that it needs to be repaired there as well as on the bottom,
Over the hive body previously pictured you can see two deeps which were cut down to mediums. Notice the three different styles of cut in handles. These three hive bodies each came from different suppliers.

This next picture is of a hive body which I simply just cut some rotten spots out of. It's easiest to me if I cut from where the joints meet in the corners and I only try to cut a minimum of wood to remove the rot. It is important to keep your cut square so when you attach the new wood to the hive body it fits properly.

This picture is of the same hive body with the new wood in place. I prefer to use a bead of carpenter's glue between the new and old wood but it is not necessary.

The other end of the hive body had some rot too. Since it was near the center of the hive body I chose to use some exterior vinyl spackling by DAP. I have used bondo before but the DAP is easier to use as it requires no mixing and is easier to sand. The reason the paint looks so bad is because it was an oil oil based paint instead of latex paint which is water based. I'll discuss the paint in more detail a little later.

It's hard to see in this picture but there is a predrilled hole into which a 3" decking screw was used to fasten the new wood to the hive body. For thinner pieces of wood used to replace rot I like to use 16d or galvanized spiral nail instead of the countersunk screws. I also favor using electrical 3/4" metal staples for securing the bottoms together to help hold them flush when screwing or stapling. After removing the paint I discovered another rotten spot. You can see where I used a chisel to remove the rot and where the DAP was used about half way down the right side of the hive body.

The next picture is of a hive body with one of the top ends repaired. There was not much damage on the top of this deep hive body but I felt the bottom was in such disrepair that it needed to be cut down to a medium super. The end had been cracked off from using it as a fulcrum to pry propolised frames from the hive body over the years. The corners were rotted and damaged as well from all the prying. Since these pieces of wood that were used are small so are the nails. A good bead of glue was applied before nailing and the glue will hold better than the nails would otherwise.

I have not painted any of the hive bodies that I have repaired because I am making and ordering more woodenware and wish to paint everything at the same time. When I paint hive bodies I prefer to use two coats of primer. My primer of choice is Kilz2 latex primer. It is a latex sealer, primer, and a stainblocker. It is also water based so cleanup only requires soap and water. It dries quickly and can be recoated in about an hour. The primer helps the paint last longer as well as it gives the paint a prepared surface suitable for painting. If you don't use primer your paint will chip off the unprepared wood in a year or two and your wood will not be properly protected from the elements.
For the paint I prefer latex. The color is not as important as what kind of paint you use. Be sure to use a water based latex exterior paint. When choosing your paint try to choose some that is mildew resistant and with a good warranty. Some people my disagree and think that oil based paint is better. However I do not share these views. Remember the green hive body above with the chipped paint? Would you like to know why it was like that? Wood is a permeable substance. This means that the wood breathes or will allow moisture to pass through it. The oil based paint creates a barrier that will not allow the wood to breath. When a strong colony of bees is curing nectar into into honey the permeable quality of is a benefit and this is one of the reasons I don't like styrofoam hives. When the moisture from the nectar tries to escape through the wood it will be trapped in behind the oil based paint. (I doubt if whiskey would be as good as it is if the charred barrels that it ages it in were painted with an oil based paint. A big part of aging whiskey in a charred barrel is that the wood breathes and allows the flavor to build during the aging process.) After a while the wood will start rotting behind the paint because it is coming from the inside. This is why I now only use latex paint because it is permeable and allows the wood to breath properly. When restoring hive bodies which have been painted with an oil based paint I use a heat gun to help strip as much of the old paint off as I can. It blisters the paint for easy scraping and removal and is much faster than sanding because the oil based paint is pretty tough stuff. If the hive bodies are properly primed and sealed before painting usually all I have to do is a little sanding just to scratch the paint up some and recoat with a fresh paint when I restore them.
Before painting there is another step that I include in my hive body rotation. Before priming and painting I will scrape the inside of the hive body. Then the inside is lightly scorched with a propane torch. After this it is then sanded until the scorching is barely visible. Though I have never had any AFB or nosema in any of my colonies for the ten years I've been keeping bees I do this as an extra precaution to help guard against spreading any possible disease that could be hiding in the propolis, burr comb, or on the wood.
I hope you enjoyed reading this and hopefully learned something to help you become a better beekeeper. When I am ready to get everything painted I'll be sure to take some pictures and to share the experience with you. Thanks for reading.
Most of the hive bodies that I use are deeps (9 5/8" tall). The deeps are much heavier when full of honey than my shallow supers are when they are full. The extra amount of pressure used to pry them apart with my hive tool also helps to damage them. After they have been in the weather for a few years the corners where you pry them apart degrade due to the weather so it becomes easier to damage them when prying them apart.
A few years ago I went to a hive body rotation schedule due to having older hive bodies which needed repaired or restored. During the winter months I will repair and restore some of the older hive bodies to rotate out with those currently in use. I like to switch them out in the spring when I start to routinely inspect my colonies. The ones which get rotated out will soon be restored or repaired with a fresh coat of primer and paint to be put back into rotation when needed. After I am finished with the rotation the last ones will usually sit around until January at which point I will start getting anxious and start the process again. The winter months are also an excellent time to buy all that new woodenware you need for the spring.
I am sure that some of you have seen hive bodies that look like this.
Sometimes when I have a hive body like this I will cut them down to a medium super (6 5/8" tall). That is the easiest thing to do. The only bad thing is that you either have to cut down some frames to fit it or just buy some new ones. You can see at the bottom left, or a top corner, of the hive body that it needs to be repaired there as well as on the bottom,
Over the hive body previously pictured you can see two deeps which were cut down to mediums. Notice the three different styles of cut in handles. These three hive bodies each came from different suppliers.
This next picture is of a hive body which I simply just cut some rotten spots out of. It's easiest to me if I cut from where the joints meet in the corners and I only try to cut a minimum of wood to remove the rot. It is important to keep your cut square so when you attach the new wood to the hive body it fits properly.
This picture is of the same hive body with the new wood in place. I prefer to use a bead of carpenter's glue between the new and old wood but it is not necessary.
The other end of the hive body had some rot too. Since it was near the center of the hive body I chose to use some exterior vinyl spackling by DAP. I have used bondo before but the DAP is easier to use as it requires no mixing and is easier to sand. The reason the paint looks so bad is because it was an oil oil based paint instead of latex paint which is water based. I'll discuss the paint in more detail a little later.
It's hard to see in this picture but there is a predrilled hole into which a 3" decking screw was used to fasten the new wood to the hive body. For thinner pieces of wood used to replace rot I like to use 16d or galvanized spiral nail instead of the countersunk screws. I also favor using electrical 3/4" metal staples for securing the bottoms together to help hold them flush when screwing or stapling. After removing the paint I discovered another rotten spot. You can see where I used a chisel to remove the rot and where the DAP was used about half way down the right side of the hive body.
The next picture is of a hive body with one of the top ends repaired. There was not much damage on the top of this deep hive body but I felt the bottom was in such disrepair that it needed to be cut down to a medium super. The end had been cracked off from using it as a fulcrum to pry propolised frames from the hive body over the years. The corners were rotted and damaged as well from all the prying. Since these pieces of wood that were used are small so are the nails. A good bead of glue was applied before nailing and the glue will hold better than the nails would otherwise.
I have not painted any of the hive bodies that I have repaired because I am making and ordering more woodenware and wish to paint everything at the same time. When I paint hive bodies I prefer to use two coats of primer. My primer of choice is Kilz2 latex primer. It is a latex sealer, primer, and a stainblocker. It is also water based so cleanup only requires soap and water. It dries quickly and can be recoated in about an hour. The primer helps the paint last longer as well as it gives the paint a prepared surface suitable for painting. If you don't use primer your paint will chip off the unprepared wood in a year or two and your wood will not be properly protected from the elements.
For the paint I prefer latex. The color is not as important as what kind of paint you use. Be sure to use a water based latex exterior paint. When choosing your paint try to choose some that is mildew resistant and with a good warranty. Some people my disagree and think that oil based paint is better. However I do not share these views. Remember the green hive body above with the chipped paint? Would you like to know why it was like that? Wood is a permeable substance. This means that the wood breathes or will allow moisture to pass through it. The oil based paint creates a barrier that will not allow the wood to breath. When a strong colony of bees is curing nectar into into honey the permeable quality of is a benefit and this is one of the reasons I don't like styrofoam hives. When the moisture from the nectar tries to escape through the wood it will be trapped in behind the oil based paint. (I doubt if whiskey would be as good as it is if the charred barrels that it ages it in were painted with an oil based paint. A big part of aging whiskey in a charred barrel is that the wood breathes and allows the flavor to build during the aging process.) After a while the wood will start rotting behind the paint because it is coming from the inside. This is why I now only use latex paint because it is permeable and allows the wood to breath properly. When restoring hive bodies which have been painted with an oil based paint I use a heat gun to help strip as much of the old paint off as I can. It blisters the paint for easy scraping and removal and is much faster than sanding because the oil based paint is pretty tough stuff. If the hive bodies are properly primed and sealed before painting usually all I have to do is a little sanding just to scratch the paint up some and recoat with a fresh paint when I restore them.
Before painting there is another step that I include in my hive body rotation. Before priming and painting I will scrape the inside of the hive body. Then the inside is lightly scorched with a propane torch. After this it is then sanded until the scorching is barely visible. Though I have never had any AFB or nosema in any of my colonies for the ten years I've been keeping bees I do this as an extra precaution to help guard against spreading any possible disease that could be hiding in the propolis, burr comb, or on the wood.
I hope you enjoyed reading this and hopefully learned something to help you become a better beekeeper. When I am ready to get everything painted I'll be sure to take some pictures and to share the experience with you. Thanks for reading.
Subscribe to:
Posts (Atom)